目前,PCB组装主要由THT和SMT组成。如何提高产品质量?要求我们掌握组装和焊接技术。特别是DIP元件,通过人工智能和手工工艺安装在PCB板上。然后我们必须了解如何选择最佳的插入方式来组装它。
电阻插入
电阻应与电路板平行并插在电路板上,元器件本体中间应安装两个孔。
<p style="color: rgb(0, 0, 0); font-family: "Calibri",sans-serif; font-size: 10.5pt; font-style: normal; font-weight: normal; margin-top: 0cm; margin-bottom: 0cm;">b. 如果阻力的长度小于构件两孔的距离,则可以立插。<p style="color: rgb(0, 0, 0); font-family: "Calibri",sans-serif; font-size: 10.5pt; font-style: normal; font-weight: normal; margin-top: 0cm; margin-bottom: 0cm;">c. 如果电阻的功率为2W或大于2W,我们不能平放在电路板上,而是水平安装,间隙为1.5mm-3mm,以免烧坏电路板。<p style="color: rgb(0, 0, 0); font-family: "Calibri",sans-serif; font-size: 10.5pt; font-style: normal; font-weight: normal; margin-top: 0cm; margin-bottom: 0cm;">电容插入
<p style="color: rgb(0, 0, 0); font-family: "Calibri",sans-serif; font-size: 10.5pt; font-style: normal; font-weight: normal; margin-top: 0cm; margin-bottom: 0cm;">a. 对于有极性要求的电容器,要注意极性的方向,必须与PCB上指示的方向一致董事会,在同时,我们应该试着把较短的针插入负片部分。注意电容器的极性。必须使径向电容器与PCB板垂直平行,另外元器件底部到电路板的距离应在0.75mm-3mm之间。
<p style="color: rgb(0, 0, 0); font-family: "Calibri",sans-serif; font-size: 10.5pt; font-style: normal; font-weight: normal; margin-top: 0cm; margin-bottom: 0cm;">二极管插入
二极管是极性元件,要确认PCB丝网上的极性标记,区分二极管的极性。千万不要插错二极管的方向,否则会影响电路板的功能,甚至导致其他元件烧坏。
<p style="color: rgb(0, 0, 0); font-family: "Calibri",sans-serif; font-size: 10.5pt; font-style: normal; font-weight: normal; margin-top: 0cm; margin-bottom: 0cm;">IC安装
所有的IC都有方向,它们的引脚排列有序。刻痕表示IC的方向,印刷电路板丝印上也有凹痕。切勿反转,否则易烧坏IC。同时,所有IC的引脚都必须插入孔中,不得有任何引脚在元件表面弯曲。
<p style="color: rgb(0, 0, 0); font-family: "Calibri",sans-serif; font-size: 10.5pt; font-style: normal; font-weight: normal; margin-top: 0cm; margin-bottom: 0cm;">Led安装
LED是极性元件,我们通常用LED管脚的长度和缺口来区分其极性。一般来说,长销的侧面为正,有缺口的部分为负
<p style="color: rgb(0, 0, 0); font-family: "Calibri",sans-serif; font-size: 10.5pt; font-style: normal; font-weight: normal; margin-top: 0cm; margin-bottom: 0cm;"> <p style="color: rgb(0, 0, 0); font-family: "Calibri",sans-serif; font-size: 10.5pt; font-style: normal; font-weight: normal; margin-top: 0cm; margin-bottom: 0cm;"> <p style="color: rgb(0, 0, 0); font-family: "Calibri",sans-serif; font-size: 10.5pt; font-style: normal; font-weight: normal; margin-top: 0cm; margin-bottom: 0cm;">我们必须了解这些基本的THT插入技术,这将有助于改进DIP元件的组装,制造出高质量的PCBA。<p style="color: rgb(0, 0, 0); font-family: "Calibri",sans-serif; font-size: 10.5pt; font-style: normal; font-weight: normal; margin-top: 0cm; margin-bottom: 0cm;">BQC是一家拥有17年经验的专业EMS PCB组装公司,拥有一支专业的工程师队伍和技术精湛的生产队伍。<p style="color: rgb(0, 0, 0); font-family: "Calibri",sans-serif; font-size: 10.5pt; font-style: normal; font-weight: normal; margin-top: 0cm; margin-bottom: 0cm;">欢迎您的询价和访厂~